Volume 42, No 2, 2020
Contents:
Effect of Abrasive Soil Mass Grain Size on the
Steel Wear Process
K. Ligier, J. Napiórkowski, M. Lemecha
Tribology in Industry, Vol. 42, No. 2, pp. 165-176, 2020
DOI: 10.24874/ti.784.10.19.04
Tribological Performance of Brass Powder with
Different Copper and Zinc Content in the Brake pad
K. Asrar Ahmed, S. Rasool Mohideen, M.A.S. Balaji,
B. Surya Rajan
Tribology in Industry, Vol. 42, No. 2, pp. 177-190, 2020
DOI: 10.24874/ti.783.10.19.03
Tribological Properties of Coatings Obtained with Electrocontact Welding of Metal Powder Materials
R. Saifullin, L. Islamov, Yu. Kuznetsov, A. Kolomeichenko,
R. Solovyev, I. Kravchenko, K. Sovin, L. Kalashnikova
Tribology in Industry, Vol. 42, No. 2, pp. 191-199, 2020
DOI: 10.24874/ti.828.01.20.03
Investigation on Tribological Behavior During
Friction Drilling Process - A Review
M. Alphonse, V.K. Bupesh Raja, M. Gupta
Tribology in Industry, Vol. 42, No. 2, pp. 200-213, 2020
DOI: 10.24874/ti.655.02.19.03
Inhibitive Action of Glutathione Reduced on
the Deterioration of AA6061 in 0.5M HCl
Nagalaxmi, P. Shetty, P.P. Kumari
Tribology in Industry, Vol. 42, No. 2, pp. 214-224, 2020
DOI: 10.24874/ti.785.10.19.02
Effect of Laser Energy on the Tribology Properties
of MoS2 Flakes
M. Mahdavi, S. Kimiagar, F. Abrinaei
Tribology in Industry, Vol. 42, No. 2, pp. 225-235, 2020
DOI: 10.24874/ti.787.11.19.02
Influence of Operating Parameters on Slurry Erosion
of Stainless Steel F6NM
I.A. Maekai, G.A. Harmain
Tribology in Industry, Vol. 42, No. 2, pp. 236-254, 2020
DOI: 10.24874/ti.780.10.19.02
The Tribological, Physico-Chemical and Rheological Properties of Lubricating Grease Produced on Epoxy
Resin Base
R. Kozdrach
Tribology in Industry, Vol. 42, No. 2, pp. 255-267, 2020
DOI: 10.24874/ti.760.09.19.04
Wear and Friction Study of Centrifugally Cast
Functionally Graded Cu-Ni-Si Alloy and Composite
S. Manu, N. Radhika
Tribology in Industry, Vol. 42, No. 2, pp. 268-277, 2020
DOI: 10.24874/ti.754.08.19.03
The Tribological Performance of Hydrodynamic
Journal Bearing Using Bio-based Lubricant
P. Zulhanafi, S. Syahrullail, M.A. Ahmad
Tribology in Industry, Vol. 42, No. 2, pp. 278-287, 2020
DOI: 10.24874/ti.843.02.20.05
Investigation of the Penetration and Temperature of
the Friction Pair Under Different Working Conditions
N. Stojanović, O.I. Abdullah, J. Schlattmann, I. Grujić, J. Glišović
Tribology in Industry, Vol. 42, No. 2, pp. 288-298, 2020
DOI: 10.24874/ti.849.02.20.05
Determining the Significance of Cobalt Addition on the Wear Characteristics of Al-6.6Si-0.4Mg Hypoeutectic
Alloy Using Design of Experiment
E.P. Sreedev, H.K. Govind, A. Raj P, S. Adithyan, H.A. Narayan, K.V. Shankar, M. Balachandran
Tribology in Industry, Vol. 42, No. 2, pp. 299-309, 2020
DOI: 10.24874/ti.777.10.19.04
Influence of Tool Tip Temperature on Crater Wear of Ceramic Inserts During Turning Process of Inconel-718
at Varying Hardness
S.I.A. Qadri, G.A. Harmain, M.F. Wani
Tribology in Industry, Vol. 42, No. 2, pp. 310-326, 2020
DOI: 10.24874/ti.776.10.19.05
Characterization and Wear Behaviour of WC-Co Coated Copper under Dry Sliding Conditions at Varying Hardness
R. Jojith, N. Radhika, R. Vigneshwar Raj
Tribology in Industry, Vol. 42, No. 2, pp. 327-336, 2020
DOI: 10.24874/ti.771.09.19.03
Efficiency Analysis of New Two-Stage Cycloid Drive Concept
M. Matejić, M. Blagojević, N. Kostić, N. Petrović, N. Marjanović
Tribology in Industry, Vol. 42, No. 2, pp. 337-343, 2020
DOI: 10.24874/ti.880.05.20.06