Volume 37, No 2, 2015
Contents:
Jenkins Model Based Ferrofluid Lubrication of a Curved Rough Annular Squeeze Film with Slip Velocity
J.R. Patel, G.M. Deheri
Tribology in Industry, Vol. 37, No. 2, pp. 129-141, 2015
Suitability of Recycled Polyethylene/Palm Kernel Shell-Iron Filings Composite for Automobile Application
I.A. Samotu, M. Dauda, F.O. Anafi, D.O. Obada
Tribology in Industry, Vol. 37, No. 2, pp. 142-153, 2015
Tribological Properties of Silicone Rubber-Based Ceramizable Composites Destined for Wire Covers.
Part I. Studies of Block-On-Ring Friction Contact
R. Anyszka, D.M. Bielinski, D. Strzelecki
Tribology in Industry, Vol. 37, No. 2, pp. 154-160, 2015
Effects of Surface Roughness in Squeeze Film Lubrication of Two Parallel Plates
J.V. Kumar, R.R. Rao
Tribology in Industry, Vol. 37, No. 2, pp. 161-169, 2015
Slew Bearings Damage Detection using Hilbert Huang Transformation and Acoustic Methods
P. Nikolakopoulos, A. Zavos
Tribology in Industry, Vol. 37, No. 2, pp. 170-175, 2015
A Comparative Experimental Study on Identification of Defect Severity in Rolling Element Bearings using Acoustic Emission and Vibration Analysis
V.V. Rao, Ch. Ratnam
Tribology in Industry, Vol. 37, No. 2, pp. 176-185, 2015
Improve Simulation of Plain Bearings in Dry and Mixed Lubrication Regime by Defining Locally Resolved Dry Friction Coefficients
C. Schneider, G. Wachtmeister, P. Klumpp, J. Halbhuber
Tribology in Industry, Vol. 37, No. 2, pp. 186-195, 2015
Analysis of Anti-Wear Properties of CuO Nanoparticles as Friction Modifiers in Mineral Oil (460cSt Viscosity) Using Pin-On-Disk Tribometer
S. Bhaumik, S.D. Pathak
Tribology in Industry, Vol. 37, No. 2, pp. 196-203, 2015
Softening Resistance, Dimensional Stability and Corrosion Behaviour of Alumina and Rice Husk Ash Reinforced Aluminium Matrix Composites Subjected to Thermal Cycling
K.K. Alaneme, Y.O. Anabaranze, S.R. Oke
Tribology in Industry, Vol. 37, No. 2, pp. 204-214, 2015
Influence of the Lubricant Type on the Surface Quality of Steel Parts Obtained by Ironing
D. Adamović, M. Stefanović, M. Živković, S. Mitrović, J. Živković, F. Živić
Tribology in Industry, Vol. 37, No. 2, pp. 215-224, 2015
Modeling and Development of RMD Configuration Magnetic Bearing
K.P. Lijesh, H. Hirani
Tribology in Industry, Vol. 37, No. 2, pp. 225-235, 2015
Multi-Criteria Analysis of Laser Cut Surface Characteristics in CO2 Laser Cutting of Stainless Steel
M. Madić, M. Radovanović, D. Petković, B. Nedić
Tribology in Industry, Vol. 37, No. 2, pp. 236-243, 2015
Wear and Friction Behavior of in-situ AA5052/ZrB2Composites under Dry Sliding Conditions
N. Kumar, R.K. Gautam, S. Mohan
Tribology in Industry, Vol. 37, No. 2, pp. 244-256, 2015
Synthesis of Uncarbonised Coconut Shell Nanoparticles: Characterisation and Particle Size Determination
S.A. Bello, S.B. Hassan, J.O. Agunsoye, M.G. Zebase Kana,
I.A. Raheem
Tribology in Industry, Vol. 37, No. 2, pp. 257-263, 2015
Study of Effect of Seal Profile on Tribological Characteristics of Reciprocating Hydraulic Seals
S. Bhaumik, A. Kumaraswamy, S. Guruprasad, P. Bhandari
Tribology in Industry, Vol. 37, No. 2, pp. 264-274, 2015